- 必威体育下载

姓名
邮箱
手机号码
标题
留言内容
验证码

摘要

本文建立了金属熔体近壁面流动剪切模型, 并分析了流动剪切对金属凝固的影响. 针对A356合金计算结果表明:层流流动的熔体内部剪应力随垂直斜板表面距离的增大而减小, 随着流动长度的增加先急剧下降之后趋于稳定; 紊流流动的熔体所受的剪应力随着垂直倾斜板表面距离的增大先急剧下降之后趋于稳定, 随着流动长度的增加而不断增大; 斜板倾角越大, 斜板上相同位置的熔体层受到的剪应力越大; 熔体垂直斜板表面距离越小, 柱状晶所承受的弯曲应力越大; 斜角越大, 斜板上相同位置的柱状晶的弯曲应力越大; 随着熔体在倾斜板表面流动长度的增加, 在层流阶段, 倾斜板表面柱状晶根部所受的弯曲应力先急剧下降之后趋于平稳, 而在紊流阶段, 弯曲应力是缓慢增加的; 理论分析表明柱状晶在熔体近壁面流动过程受到的最大弯曲应力低于αup -Al晶粒的屈服强度, 所以斜板上熔体流动产生的弯曲力不能将柱状晶折断, 只能将晶粒冲刷游离到熔体中使晶粒增殖, 与实验结果相符合. 所以本模型可以很好地解释熔体近壁面流动过程中的剪切本构关系以及剪应力对凝固组织的影响.

关键词:

凝固/
近壁面流动/
剪切/
柱状晶

Abstract

In this paper, the model of metalic melt shearing flow near the surface is established, and the effect of shearing flow on solidification microstructure of the metal is also analyzed. Calculated results based on A356 alloy melt show that in the laminar flowing melt, the shear stress decreases with increasing length along the vertical direction of the surface of the slope, and the shear stress first decreases rapidly and then stabilizes with increasing length along the flowing direction of the surface of the slope; while in the turbulent flowing melt, the shear stress firstly decreases rapidly and then stabilizes with increasing length along the vertical direction of the surface of the slope, and increases with increasing length along the flowing direction of the surface of the slope. The shear stress at the same position in the melt on the surface of the slope increases with increasing angle of the slope; the shear stress acting on the columnar crystal in the melt on the surface of the slope increases with decreasing length along the vertical direction of the surface of the slope. The shear stress acting on the columnar crystal at the same position in the melt on the surface of the slope increases with increasing angle of the slope; with the increase of the length along the flowing direction, the shear stress acting on the columnar crystal rapidly decreases first and then stabilizes in the laminar flowing melt on the surface of the slope, while the shear stress increases in the turbulently flowing melt on the surface of the slope. Based on the theoretical calculation, the maximum shear stress acting on the columnar crystal in the melt during the shearing flow near the surface of the metalic melt is lower than the yield strength of α-Al grain, so the shear stress induced by shearing flow cannot break the columnar crystal, and only by sweeping the grain into the melt to induce the multiplication of grain, which agrees with the experimental results. So, the proposed model can explain the constitutive relations of the metalic melt shearing flow near the surface and the effect of shear stress on the solidification microstructure.

Keywords:

作者及机构信息

1.
2.
3.

基金项目:国家自然科学基金(批准号:51222405,51474063)资助的课题.

Authors and contacts

1.
2.
3.

Funds:Project supported by the National Natural Science Foundation of China (Grant Nos. 51222405, 51474063).

参考文献

[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]

施引文献

[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]

[1]	方芳, 鲍麟, 童秉纲.基于斜驻点模型的剪切层撞击壁面流动及传热特性. 必威体育下载 , 2020, 69(21): 214401.doi:10.7498/aps.69.20201000
[2]	游家学, 王锦程, 王理林, 王志军, 李俊杰, 林鑫.悬浮液凝固研究进展. 必威体育下载 , 2019, 68(1): 018101.doi:10.7498/aps.68.20181645
[3]	张冉, 谢文佳, 常青, 李桦.纳米通道内气体剪切流动的分子动力学模拟. 必威体育下载 , 2018, 67(8): 084701.doi:10.7498/aps.67.20172706
[4]	孟广慧, 林鑫.二元层片共晶凝固过程的特征尺度选择. 必威体育下载 , 2014, 63(6): 068104.doi:10.7498/aps.63.068104
[5]	陈海楠, 孙东科, 戴挺, 朱鸣芳.凝固前沿和气泡相互作用的大密度比格子玻尔兹曼方法模拟. 必威体育下载 , 2013, 62(12): 120502.doi:10.7498/aps.62.120502
[6]	苑轶, 李英龙, 王强, 刘铁, 高鹏飞, 赫冀成.强磁场对Mn-Sb包晶合金相变及凝固组织的影响. 必威体育下载 , 2013, 62(20): 208106.doi:10.7498/aps.62.208106
[7]	张松鹏, 张向军, 田煜, 孟永钢.采用液晶涂层测量介质流与壁面间剪切应力的定量模型与试验研究. 必威体育下载 , 2012, 61(23): 234702.doi:10.7498/aps.61.234702
[8]	潘诗琰, 朱鸣芳.双边扩散枝晶生长的定量相场模型. 必威体育下载 , 2012, 61(22): 228102.doi:10.7498/aps.61.228102
[9]	李国建, 王强, 曹永泽, 吕逍, 李东刚, 赫冀成.初始温度和冷却速率对金属团簇凝固行为的影响. 必威体育下载 , 2011, 60(9): 093601.doi:10.7498/aps.60.093601
[10]	赵雪川, 刘小明, 高原, 庄茁.剪切作用下Cu(100)扭转晶界塑性行为研究. 必威体育下载 , 2010, 59(9): 6362-6368.doi:10.7498/aps.59.6362
[11]	王春江, 苑轶, 王强, 刘铁, 娄长胜, 赫冀成.强磁场条件下金属凝固过程中第二相的迁移行为. 必威体育下载 , 2010, 59(5): 3116-3122.doi:10.7498/aps.59.3116
[12]	徐送宁, 张林, 张彩碚, 祁阳.熔融Cu55团簇在铜块体中凝固过程的分子动力学模拟. 必威体育下载 , 2009, 58(13): 40-S46.doi:10.7498/aps.58.40
[13]	张宗宁, 刘美林, 李蔚, 耿长建, 赵骞, 张林.熔融Cu55团簇在Cu(010)表面上凝固过程的分子动力学模拟. 必威体育下载 , 2009, 58(13): 67-S71.doi:10.7498/aps.58.67
[14]	单博炜, 林鑫, 魏雷, 黄卫东.纯物质枝晶凝固的元胞自动机模型. 必威体育下载 , 2009, 58(2): 1132-1138.doi:10.7498/aps.58.1132
[15]	王狂飞, 李邦盛, 任明星, 米国发, 郭景杰, 傅恒志.Ti-44at%Al合金小尺寸铸件柱状晶/等轴晶演化过程模拟. 必威体育下载 , 2007, 56(6): 3337-3343.doi:10.7498/aps.56.3337
[16]	王海燕, 刘日平, 马明臻, 高明, 姚玉书, 王文魁.FeSi2合金在高压下的凝固. 必威体育下载 , 2004, 53(7): 2378-2383.doi:10.7498/aps.53.2378
[17]	黄卫东, 林　鑫, 李　涛, 王琳琳, Y. Inatomi.单相合金凝固过程时间相关的界面稳定性(Ⅱ)实验对比. 必威体育下载 , 2004, 53(11): 3978-3983.doi:10.7498/aps.53.3978
[18]	张林, 王绍青, 叶恒强.大角度Cu晶界在升温、急冷条件下晶界结构的分子动力学研究. 必威体育下载 , 2004, 53(8): 2497-2502.doi:10.7498/aps.53.2497
[19]	李　强, 李殿中, 钱百年.元胞自动机方法模拟枝晶生长. 必威体育下载 , 2004, 53(10): 3477-3481.doi:10.7498/aps.53.3477
[20]	刘俊明.层状共晶定向凝固. 必威体育下载 , 1992, 41(5): 861-868.doi:10.7498/aps.41.861

计量

文章访问数:5040
PDF下载量:189
被引次数:0

搜索

留言板

Theoretical study on the model of metalic melt shearing flow near the surface and its effect on solidification microstructure

摘要

Abstract

作者及机构信息

1.
2.
3.

Authors and contacts

1.
2.
3.

参考文献

施引文献

目录

计量

作者中心

必威betway88欢迎你

关于期刊

关于我们

搜索

留言板

Theoretical study on the model of metalic melt shearing flow near the surface and its effect on solidification microstructure

摘要

Abstract

作者及机构信息

1.2.3.

Authors and contacts

1.2.3.

参考文献

施引文献

目录

计量

出版历程

作者中心

必威betway88欢迎你

关于期刊

关于我们

1.
2.
3.

1.
2.
3.