-
基于构形理论, 以(火积)耗散率最小为优化目标, 对冷却流道的“盘点”传热问题进行构形优化, 得到冷却流道的圆盘构造体最优构形. 结果表明: 对于扇形单元体, 在其泵功率给定的条件下, 存在最佳展弦比使得扇形单元体无量纲当量热阻取得最小值; 对于一级树状圆盘, 在其总泵功率给定的条件下, 存在一级与单元级最佳流道宽度比和扇形单元体最佳无量纲半径使 得一级树状圆盘无量纲当量热阻取得最小值, 且一级与单元级最佳流道宽度比仅与单元体分支数有关. 当中心圆盘半径等于0时, 一级树状圆盘最终退化成辐射状圆盘, 此时一级树状圆盘半径为临界半径. 当一级树状圆盘半径大于临界半径时, 需对圆盘冷却流道采用树状布置, 反之则采用辐射状布置. 存在最佳单元体分支数使得无量纲当量热阻取得最小值, 这与高导热材料通道的“盘点”导热构形优化结果有明显区别. (火积)耗散率最小和最大温差最小的一级树状冷却流 道圆盘构造体最优构形是不同的. 与最大温差最小的冷却流道圆盘构造体相比, (火积)耗散率最小的冷却流道圆盘构造体当量热阻得到极大降低, 其整体传热性能得到明显提高. 因此, (火积)耗散极值原理与对流构形优化相结合, 有助于进一步揭示(火积)耗散极值原理在传热优化方面的优越性.Based on configucation theory, the construction of a “disc-point” heat transfer with cooling channels can be optimized by taking minimum entransy dissipation rate. Thus an optimal construction of the disc-shaped assembly with cooling channels is obtained. The results show that there exists an optimal aspect ratio of the elemental sector which leads to the minimum dimensionless equivalent thermal resistance of the elemental sector at the fixed pumping power; there also exists an optimal width ratio of the elemental and first-order cooling channel to the optimal dimensionless radius of the elemental sector, which leads to the minimum dimensionless equivalent thermal resistance of the first-order branched-pattern disc at the fixed total pumping power. Moreover, the optimal width ratio of the elemental and first-order cooling channels is only relative to the number of elemental tributaries. When the radius of the central disc tends to zero, the branch-pattern disc is simplified into a radial-pattern disc, and the radius of the first-order branch-pattern disc becomes the critical radius at this point. When the radius of the branch-pattern disc is higher than the critical radius, the branch-pattern design should be adopted, otherwise the radial-pattern design should be adopted. There exists an optimal number of elemental tributaries which lead to the minimum dimensionless equivalent thermal resistance of the first-order branch-pattern disc, which is obviously different from the results of the “disc-point” heat conduction constructional optimization with high-conductivity channels. The optimal constructions of the first-order branch-pattern disc based on the minimizations of entransy dissipation rate and maximum temperature difference are different. The dimensionless equivalent thermal resistance of the disc with cooling channels based on the minimization of entransy dissipation rate is greatly reduced as compared with that based on the minimization of maximum temperature difference, and its global heat transfer performance is obviously improved simultaneously. Therefore, the combination of the entransy dissipation extremum principle and the heat convection constructional optimization further illustrates the advantages of minimization of entransy dissipation rate for heat transfer optimizations.
-
Keywords:
- constructal theory/
- entransy dissipation rate/
- cooling channels/
- generalized thermodynamic optimization
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] [24] [25] [26] [27] [28] [29] [30] [31] [32] [33] [34] [35] [36] [37] [38] -
[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] [24] [25] [26] [27] [28] [29] [30] [31] [32] [33] [34] [35] [36] [37] [38]
计量
- 文章访问数:6042
- PDF下载量:623
- 被引次数:0