- 必威体育下载

姓名
邮箱
手机号码
标题
留言内容
验证码

摘要

采用耦合群体动力学方法与元胞自动机方法建立了细化处理条件下铝合金凝固微观组织演变的数值模型. 该模型考虑了 α-Al的非均匀形核过程、晶粒的初始球形长大以及之后的枝晶生长过程. 利用建立的模型模拟了Al-5Ti-1B中间合金细化工业纯铝凝固组织演变过程. 结果表明: 形核初始阶段, 熔体中存在充足数量的有效形核粒子, α-Al形核率随着熔体过冷度的增大逐渐增高; 形核开始不久后, α-Al的异质形核过程由熔体中有效形核粒子数量控制, 直到再辉发生, 形核停止. 模拟分析了中间合金添加量以及熔体冷却速度对工业纯铝凝固组织演变过程的影响, 模拟结果与实验结果相符, 验证了模型的准确性.

关键词:

铝合金/
形核/
晶粒生长/
模拟

Abstract

Solidification microstructure of aluminum alloy has a great influence on the properties of the casting. An aluminum alloy with the structure of fine equiaxed grains has low casting defects and presents excellent mechanical properties. Recently, chemical inoculation by adding grain refiner is the technique most extensively used to achieve a fine, equiaxed grain structure of Al alloy in the industrial production. In order to investigate the detailed solidification microstructure evolution of the alloy, many numerical models have been proposed. Cellular automaton method is one of the powerful tools for simulating the morphology evolution of detailed grains in the solidification process of alloy. However, the present cellular automata model has a shortcoming, that is, its calculation of the nucleation rate is based on the experimental number density of grains. In this work, a population dynamics-cellular automaton model is developed for describing the solidification microstructure evolution of the inoculated aluminum alloy. The model takes account of the heterogeneous nucleation of α-Al nucleus, the initial spherical growth of α-Al grains and the dendritic growth process. The model is used for simulating the solidification microstructure evolution of the commercial-purity aluminum (CP-Al) inoculated by Al-5Ti-1B master alloy. The results indicate that the heterogeneous nucleation process of α-Al can be divided into the two stages. In the early stage of nucleation, there are enough effective particles in the melt. The nucleation rate of α-Al increases with the increase of the undercooling of the melt. After a short time, the nucleation of α-Al is dominated by the number density of the effective particles in the melt. Nucleation process stops when the recalescence takes place. The effects of the additive amount of Al-5Ti-1B master alloy and the cooling rate of the melt on the solidification microstructure of the CP-Al are investigated by using the established model. The final solidification structures of CP-Al are predicted. And a comparison between the predicted results and the experimental ones shows that they are in good agreement with each other.

Keywords:

作者及机构信息

1.
2.

通信作者:江鸿翔,hxjiang@imr.ac.cn; 赵九洲,jzzhao@imr.ac.cn;

基金项目:中国科学院空间科学战略性先导科技专项(批准号: XDA15013800)、辽宁省自然科学基金(批准号: 2020-MS-005)和国家自然科学基金(批准号: 51771210, 51501207, 51971227)资助的课题

Authors and contacts

1.
2.

Corresponding author:Jiang Hong-Xiang,hxjiang@imr.ac.cn; Zhao Jiu-Zhou,jzzhao@imr.ac.cn;

Funds:Project supported by the Chinese Academy of Sciences Strategic Priority Program on Space Science, China (Grant No. XDA15013800), the Natural Science Foundation of Liaoning Province, China (Grant No. 2020-MS-005), and the National Natural Science Foundation of China (Grant Nos. 51771210, 51501207, 51971227)

文章全文: translate this paragraph

参考文献

[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]

施引文献

下载: 全尺寸图片幻灯片

Element	Liquidus slope,m	Partition coefficient,k	Solute composition/% (weight percent)	Q
Fe	–2.925	0.030	0.0825	0.234
Si	–6.62	0.120	0.0475	0.276
Ga	–2.52	0.140	0.0125	0.028
Ni	–3.50	0.004	0.0051	0.018
V	9.71	3.330	0.0079	0.167
Ti	25.63	7.000	0.0042	0.63
Na	–7.84	0.013	0.0015	0.012

下载: 导出CSV

Parameter	Value
Cooling rate of the CP-Al melt/(K·s^–1)	3.5
Strength of the anisotropy of the interfacial energy,ε	0.04
Gibbs-Thomson coefficient, $\varGamma $/mK	1.42 × 10⁷
Heat capacity of Al melt,C_P/(J·K^–1·m³)	2.58 × 10⁶
Average jump distance of Al atoms in Al melt,δ/m	2.87 × 10^–10
Boltzmann’s constant,k_B	1.38 × 10^–23

下载: 导出CSV

[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]

[1]	张伟光, 张凯奋, 夏立东, 黄鑫, 周晓松, 彭述明, 施立群.氘氚冰籽晶的形核行为. 必威体育下载 , 2022, 71(2): 025203.doi:10.7498/aps.71.20211018
[2]	姜彦博, 柳文波, 孙志鹏, 喇永孝, 恽迪.外加应力作用下 UO₂中空洞演化过程的相场模拟. 必威体育下载 , 2022, 71(2): 026103.doi:10.7498/aps.71.20211440
[3]	戴宇佳, 李明亮, 宋超, 高勋, 郝作强, 林景全.空间约束结合梯度下降法提高铝合金中Fe成分激光诱导击穿光谱技术检测精度. 必威体育下载 , 2021, 70(20): 205204.doi:10.7498/aps.70.20210792
[4]	陈熙, 林正喆, 殷聪, 汤浩, 胡蕴成, 宁西京.铂纳米颗粒生长和表面结构的理论预测. 必威体育下载 , 2012, 61(7): 076801.doi:10.7498/aps.61.076801
[5]	张宪刚, 宗亚平, 吴艳.相场再结晶储能释放模型与显微组织演变的模拟研究. 必威体育下载 , 2012, 61(8): 088104.doi:10.7498/aps.61.088104
[6]	魏承炀, 李赛毅.温度梯度对晶粒生长行为影响的相场模拟. 必威体育下载 , 2011, 60(10): 100701.doi:10.7498/aps.60.100701
[7]	孙对兄, 苏茂根, 董晨钟, 王向丽, 张大成, 马新文.基于激光诱导击穿光谱技术的铝合金成分定量分析. 必威体育下载 , 2010, 59(7): 4571-4576.doi:10.7498/aps.59.4571
[8]	刘耀民, 刘中良, 黄玲艳.分形理论结合相变动力学的冷表面结霜过程模拟. 必威体育下载 , 2010, 59(11): 7991-7997.doi:10.7498/aps.59.7991
[9]	王娜, 唐壁玉.L12型铝合金的结构、弹性和电子性质的第一性原理研究. 必威体育下载 , 2009, 58(13): 230-S234.doi:10.7498/aps.58.230
[10]	樊飞, 班春燕, 王洋, 巴启先, 崔建忠.普通铸造和低频电磁铸造7050铝合金电阻率-温度特性的研究. 必威体育下载 , 2009, 58(1): 638-643.doi:10.7498/aps.58.638
[11]	张华伟, 李言祥.金属熔体中气泡形核的理论分析. 必威体育下载 , 2007, 56(8): 4864-4871.doi:10.7498/aps.56.4864
[12]	庞雪君, 王强, 王春江, 王亚勤, 李亚彬, 赫冀成.强磁场对铝合金中溶质组元分布状态的影响效果. 必威体育下载 , 2006, 55(10): 5129-5134.doi:10.7498/aps.55.5129
[13]	彭开萍, 陈文哲, 钱匡武.3004铝合金“反常”锯齿屈服现象的研究. 必威体育下载 , 2006, 55(7): 3569-3575.doi:10.7498/aps.55.3569
[14]	路阳, 王帆, 朱昌盛, 王智平.等温凝固多晶粒生长相场法模拟. 必威体育下载 , 2006, 55(2): 780-785.doi:10.7498/aps.55.780
[15]	段鹤, 郑毓峰, 张校刚, 孙言飞, 董有忠.水热法合成FeS2粉晶及其生长热动力学的研究. 必威体育下载 , 2005, 54(4): 1659-1664.doi:10.7498/aps.54.1659
[16]	吴汉华, 龙北红, 吕宪义, 汪剑波, 金曾孙.铝合金微弧氧化过程中电学参量的特性研究. 必威体育下载 , 2005, 54(4): 1697-1701.doi:10.7498/aps.54.1697
[17]	黄文, 曾慧中, 张鹰, 蒋书文, 魏贤华, 李言荣.不同晶化工艺对非晶PZT纳米薄膜形核取向生长机理的影响. 必威体育下载 , 2005, 54(3): 1334-1340.doi:10.7498/aps.54.1334
[18]	黄　锐, 林璇英, 余云鹏, 林揆训, 姚若河, 黄文勇, 魏俊红, 王照奎, 余楚迎.多晶硅薄膜低温生长中晶粒大小的控制. 必威体育下载 , 2004, 53(11): 3950-3955.doi:10.7498/aps.53.3950
[19]	张建民, 徐可为.银和铜膜中异常晶粒生长和织构变化的实验研究. 必威体育下载 , 2003, 52(1): 145-149.doi:10.7498/aps.52.145
[20]	王培林, 丁天骅, 蔡珣.超薄晶体膜生长过程的计算机模拟. 必威体育下载 , 2002, 51(9): 2109-2112.doi:10.7498/aps.51.2109

计量

文章访问数:5425
PDF下载量:106
被引次数:0

搜索

留言板